Revision as of 08:00, 3 August 2013 by Craig Peacock (Talk | contribs)

By default, the ROM in the Sitara AM3359 will boot from MMC1 first (the onboard eMMC), followed by MCC0 (MicroSD), UART0 and USB0.

If the boot switch (S2) is held down, the ROM will boot from SPI0 first, followed by MMC0, USB0 and UART0. This allows the BeagleBone Black to bypass the onboard eMMC and boot from the removable uSD (provided no valid boot device is found on SPI0.)

The Sitara AM3359 will try to load and execute the first stage bootloader called "MLO" from a Fat 12/16 or 32 bit MBR based filesystem.

MLO Booting:

U-Boot SPL 2013.04-dirty (Jun 19 2013 - 09:57:14)
musb-hdrc: ConfigData=0xde (UTMI-8, dyn FIFOs, HB-ISO Rx, HB-ISO Tx, SoftConn)
musb-hdrc: MHDRC RTL version 2.0 
musb-hdrc: setup fifo_mode 4
musb-hdrc: 28/31 max ep, 16384/16384 memory
USB Peripheral mode controller at 47401000 using PIO, IRQ 0
musb-hdrc: ConfigData=0xde (UTMI-8, dyn FIFOs, HB-ISO Rx, HB-ISO Tx, SoftConn)
musb-hdrc: MHDRC RTL version 2.0 
musb-hdrc: setup fifo_mode 4
musb-hdrc: 28/31 max ep, 16384/16384 memory
USB Host mode controller at 47401800 using PIO, IRQ 0
OMAP SD/MMC: 0
mmc_send_cmd : timeout: No status update
reading u-boot.img
reading u-boot.img

MLO is a first stage uBoot Bootloader designed to load a second stage uBoot bootloader with enhanced features. This second stage bootloader is also found on the FAT partition with the filename of "u-boot.img"

U-Boot 2013.04-dirty (Jun 19 2013 - 09:57:14)

I2C:   ready
DRAM:  512 MiB
WARNING: Caches not enabled
NAND:  No NAND device found!!!
0 MiB
MMC:   OMAP SD/MMC: 0, OMAP SD/MMC: 1
*** Warning - readenv() failed, using default environment

musb-hdrc: ConfigData=0xde (UTMI-8, dyn FIFOs, HB-ISO Rx, HB-ISO Tx, SoftConn)
musb-hdrc: MHDRC RTL version 2.0 
musb-hdrc: setup fifo_mode 4
musb-hdrc: 28/31 max ep, 16384/16384 memory
USB Peripheral mode controller at 47401000 using PIO, IRQ 0
musb-hdrc: ConfigData=0xde (UTMI-8, dyn FIFOs, HB-ISO Rx, HB-ISO Tx, SoftConn)
musb-hdrc: MHDRC RTL version 2.0 
musb-hdrc: setup fifo_mode 4
musb-hdrc: 28/31 max ep, 16384/16384 memory
USB Host mode controller at 47401800 using PIO, IRQ 0
Net:   <ethaddr> not set. Validating first E-fuse MAC
cpsw, usb_ether
Hit any key to stop autoboot:  1  0 
gpio: pin 53 (gpio 53) value is 1
Card did not respond to voltage select!
mmc0(part 0) is current device
mmc_send_cmd : timeout: No status update
Card did not respond to voltage select!
No micro SD card found, setting mmcdev to 1
mmc1(part 0) is current device
gpio: pin 54 (gpio 54) value is 1
SD/MMC found on device 1
reading uEnv.txt
26 bytes read in 2 ms (12.7 KiB/s)
Loaded environment from uEnv.txt
Importing environment from mmc ...
gpio: pin 55 (gpio 55) value is 1
4270840 bytes read in 747 ms (5.5 MiB/s)
gpio: pin 56 (gpio 56) value is 1
24129 bytes read in 53 ms (444.3 KiB/s)
Booting from mmc ...